BEHRINGER EUROPOWER EP1500

 

The Behringer EP1500 Europower is an extremely musical power amp that can take a whole night’s worth of abuse without missing a beat—even at 2 Ohms!
The EP1500 Europower is a dependable workhorse that will never let you down. You get enough real-world Watts to get you through the roughest gigs: 2 x 700 Watts into 2 Ohms, or 1,400 Watts into 4 Ohms bridged mono operation. Experience has probably taught you that there is nothing worse than when your amp runs out of breath. With Europower, you’ve got your back covered all the way. From the deepest bass all the way up to the most subtle highs, you will be amazed at the clarity and richness of sound.

This kind of multi-faceted performance was previously possible only with amps costing hundreds more. The EP1500 Europower meets the needs of professional musicians, for both installed applications or on the road. No corners were cut in the design process. You can rest assured that these are tough, reliable amps built to last and last. After all, you have come to expect nothing less from BEHRINGER. XLR and 1/4-inch inputs, Speakon and binding post outputs.

Getting all the gear you need to complete your PA system can be a chore. AMS offers complete PA packages that take the guesswork out, and make assembling the perfect sound system easy—while saving you money. Click Here to see all the details.

Each EUROPOWER has a massive power supply with a low-noise toroidal transformer and lots of headroom, so your music sounds great—even when you push the amp to the limit—and it stays that way! Add an extremely effective cooling system and you have an amp that is guaranteed to be trouble-free.

Further underscoring Behringer's serious commitment to excellence, they use only high-quality, high-speed FAIRCHILD and TOSHIBA transistors that are second to none. As with all Behringer products, the EUROPOWER Series is manufactured in accordance with the ISO9000 certified management and manufacturing system, resulting in a high-quality product that will survive years of the toughest use.

 

BEHRINGER EUROPOWER EP2500

  • 2 x 1,200 Watts into 2 Ohms; 2,400 Watts into 4 Ohms bridged operation

  • 2-channel, parallel or bridged mono operating modes for flexible application

  • Independent limiters for each channel offer dependable protection against distortion

  • Precise signal and clip LED indicators to monitor performance

  • Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies

  • Professional connectors, compatible with Neutrik Speakon connectors, and “touch-proof” binding post loudspeaker outputs enable secure operation

  • Balanced XLR and 1/4" TRS inputs

  • Connection option for extra amps in parallel operation

  • Ultra-reliable Toshiba/Fairchild high-power transistors

  • High-current toroidal transformer for absolute reliability and lowest noise emission

  • “Back-to-front” ventilation system including air filter with automatically adjusting fan speed for smooth operation

  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers

  • High-quality components and exceptionally rugged construction ensure long life

BEHRINGER EUROPOWER EP2000

  • 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)

  • Precise Power, Signal and Clip LEDs to monitor performance

  • XLR and 1/4" TRS input connectors for compatibility with any source

  • Professional speaker connectors and “touch-proof” binding posts support most speaker wiring systems

  • Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies

  • Independent limiters per channel offer reliable protection against overload and distortion

  • High-current toroidal transformer for ultra-high transient response and absolute reliability

  • Ultra-reliable Toshiba/Fairchild power transistors

  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show

  • “Back-to-front” ventilation system including air filter for reliable operation

  • “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis

  • High-quality components and exceptionally rugged construction ensure long life

BEHRINGER EUROPOWER EPX2000

 

Power amps have always been heavy, mainly because of the massive transformers and heat sinks. Our new EPX Series amps are based on groundbreaking switch-mode technology which eliminates the heavy transformer. As a result, the amp weighs around 40% less - in fact the EPX2000 is just 22 lbs./10.10 kg, and you can lift it up almost with one finger. Best of all our super-reliable switch-mode power supply provides an even tighter bass performance as it can deliver ultra-high peak currents.

  • 2 x 1,000 Watts into 2 Ohms; 2 x 650 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)

  • ATR (Accelerated Transient Response) technology for ultimate punch and clarity

  • Ultra-light, ultra-low noise and ultra-efficient switch-mode power supply for noise-free audio, superior transient response and low power consumption

  • Switchable limiters offer maximum output level with reliable overload protection

  • Detented gain controls for precise setting and matching of sensitivity

  • Precise Power, Signal and Clip LEDs to monitor performance

  • XLR, 1/4" TRS and RCA input connectors for compatibility with any source

  • Professional speaker connectors and "touch-proof" binding posts support most speaker wiring systems

  • Built-in Subwoofer/Satellite crossover for more flexibility

  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show

  • “Back-to-front” ventilation system including air filter for reliable operation

  • "Built-like-a-tank", impact-resistant, all-steel 2U rackmount chassis

  • High-quality components and exceptionally rugged construction ensure long life

BEHRINGER EUROPOWER EPX3000

 

Professional 3,000-Watt Light Weight Stereo Power Amplifier with ATR (Accelerated Transient Response) Technology

  • 2 x 1,500 Watts into 2 Ohms; 2 x 900 Watts into 4 Ohms; 3,000 Watts into 4 Ohms (bridge mode)

  • ATR (Accelerated Transient Response) technology for ultimate punch and clarity

  • Ultra-light, ultra-low noise and ultra-efficient switch-mode power supply for noise-free audio, superior transient response and low power consumption

  • Switchable limiters offer maximum output level with reliable overload protection

  • Detented gain controls for precise setting and matching of sensitivity

  • Precise Power, Signal and Clip LEDs to monitor performance

  • XLR , 1/4" TRS and RCA input connectors for compatibility with any source

  • Professional speaker connectors and "touch-proof" binding posts support most speaker wiring systems

  • Built-in Subwoofer/Satellite crossover for more flexibility

  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show

  • “Back-to-front” ventilation system including air filter for reliable operation

  • "Built-like-a-tank", impact-resistant, all-steel 2U rackmount chassis

  •  High-quality components and exceptionally rugged construction ensure long life

  • High-quality components and exceptionally rugged construction ensure long life

BEHRINGER EUROPOWER EP4000

  • 2 x 2,000 Watts into 2 Ohms; 2 x 1,400 Watts into 4 Ohms; 4,000 Watts into 4 Ohms (bridge mode)

  • Precise Power, Signal and Clip LEDs to monitor performance

  • XLR and 1/4" TRS input connectors for compatibility with any source

  • Professional speaker connectors and "touch-proof" binding posts support most speaker wiring systems

  • Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies

  • Independent limiters per channel offer reliable protection against overload and distortion

  • High-current toroidal transformer for ultra-high transient response and absolute reliability

  • Ultra-reliable Toshiba/Fairchild power transistors

  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show

  • "Back-to-front" ventilation system including air filter for reliable operation

  • "Built-like-a-tank," impact-resistant, all-steel 2U rackmount chassis

  • High-quality components and exceptionally rugged construction ensure long life

CREST CPX1500

 

Gain Comparator Limiting. When a signal has waveform peaks that exceed the amps' power-supply rails, waveforms get chopped off, or “clipped." This undesirable distortion most often happens when the amp is turned up too high (too much gain). GCL™ senses clipping (or current limiting) and dynamically reduces the gain for a few milliseconds. You can drive the CPX amp to its maximum (and beyond) without hearing audible distortion. Don't settle for less. If you need maximum performance on a tight budget, you owe it to yourself to get your hands on a CPX Series amplifier from Crest Performance.

 

CREST CPX900

 

Gain Comparator Limiting. When a signal has waveform peaks that exceed the amps' power-supply rails, waveforms get chopped off, or “clipped." This undesirable distortion most often happens when the amp is turned up too high (too much gain). GCL™ senses clipping (or current limiting) and dynamically reduces the gain for a few milliseconds. You can drive the CPX amp to its maximum (and beyond) without hearing audible distortion. Don't settle for less. If you need maximum performance on a tight budget, you owe it to yourself to get your hands on a CPX Series amplifier from Crest Performance

 

CROWN XLS402

 

The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified.

  • Sensitivity (volts RMS) for full rated power at 4 ohms: 1.025

  • Frequency Response (at 1 watt) 20 Hz to 20 kHz: Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25

  • Frequency Response (at 1 watt, 22 Hz - 20 kHz): +0 dB, -1 dB

  • Signal to Noise Ratio below rated power (20 Hz to 20 kHz, inputs terminated)

  • A-weighted, below rated power: > 100 dB

  • No weighting, below rated power: > 95 dB

  • Total Harmonic Distortion (THD) at 1 full bandwidth power, from 20 Hz to 1 kHz:
    < 0.5%

  • Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to -30 dB: < 0.3%

  • Damping Factor (8 ohm): 10 Hz to 400 Hz: > 200

  • Crosstalk (below rated power):
    - at 1 kHz: -75 dB
    - at 20 kHz: -50 dB

  • Input Impedance (nominal) (balanced, unbalanced): 20 kilohms, 10 kilohms

  • Load impedance
    - Stereo: 4-8 ohms
    - Bridge mono: 8 ohms

CROWN XLS602

  • Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.

  • Crosstalk (below rated power)
    at 1 kHz: +76 dB. at 20 kHz: +58 dB.

  • Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced.

  • Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono.

  • The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified.

  • Sensitivity (volts RMS) for full rated power at 4 ohms: 1.025

  • Frequency Response (at 1 watt) 20 Hz to 20 kHz: Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25

  • Frequency Response (at 1 watt, 22 Hz - 20 kHz): +0 dB, -1 dB

  • Signal to Noise Ratio below rated power (20 Hz to 20 kHz, inputs terminated)

  • A-weighted, below rated power: > 100 dB

  • No weighting, below rated power: > 95 dB

  • Total Harmonic Distortion (THD) at 1 full bandwidth power, from 20 Hz to 1 kHz:
    < 0.5%

  • Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to -30 dB: < 0.3%

  • Damping Factor (8 ohm): 10 Hz to 400 Hz: > 200

  • Crosstalk (below rated power):
    - at 1 kHz: -75 dB
    - at 20 kHz: -50 dB

  • Input Impedance (nominal) (balanced, unbalanced): 20 kilohms, 10 kilohms

  • Load impedance
    - Stereo: 4-8 ohms
    - Bridge mono: 8 ohms

  • AC Line Voltage and Frequency Configurations Available (+/- 10%):
    - 120 VAC 60 Hz
    - 100 VAC 50/60 Hz
    - 220 VAC 50 Hz
    - 230-240 VAC 50 Hz

  • Ventilation: Flow-through ventilation from front to back

  • Cooling: Internal heat sinks with forced-air cooling

  • Air Volume Requirements (per minute per unit): 80.15 ft3 (2.27 m3)

CROWN XLS802

  • Damping Factor (8 ohm) 10 Hz to 400 Hz: >200

  • Crosstalk (below rated power) at 1 kHz: +76 dB. at 20 kHz: +58 dB

  • Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced

  • Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono

  • AC Line Voltage and Frequency Configurations Available (+/-10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC

  • Controls
    Level: 2 front-panel rotary level controls, 1 for each channel

  • Power: Front-panel switch; on when in the IN position

  • Circuit Breaker: Back-panel breaker provides overload protection

  • Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode

  • Indicators
    Signal Presence Indicators: 2 green LEDs, one for each channel, illuminate when the channel's input signal exceeds +40 dBu

  • Clip Indicators: 2 red LEDs, 1 for each channel, illuminate when the channel's output is being overdriven

  • Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available

  • Fault Indicator: 2 red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on

  • Input/Output
    Input Connectors: 1 per channel; back-panel 3-pin female XLR input connectors

  • Output Connectors: Two 4-Pole Speakon Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector. One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.)

  • Protection
    XLS Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, DC protection, circuit breaker, and thermal protection.

  • Construction
    Ventilation: Flow-through ventilation from front to back

  • Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation

  • Air Volume Requirements (per minute per unit): 80.15 cubic ft.

  • Dimensions: EIA Standard 19 in. (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 15.2 in. (38.6-cm) depth

  • Net Weight: 35.5 lb (16.1 kg)

  • Shipping Weight: 40.5 lb (18.4 kg)

PEAVEY CS1400

 

The Peavey CS1400 PA power amplifier, is the culmination of 20 years of continuous improvement and is capable of delivering 1400 Watts (bridged) at 4 ohms.

The Peavey CS1400 is the global standard bearer for workhorse reliability. Over the years, these amps have benefited from some of Peavey's most popular audio innovations, including the exclusive DDT compression/anti-clipping protection. With its 2RU design and power up to 1400 watts, this latest evolution of the CS(R) Series is leaner, louder and lighter than ever.

Peavey CS1400 features include:

  • 2-rack-space stereo power amp featuring DDT

  • Two temperature-dependant dual-speed fans

  • 700 watts RMS per channel at 2 ohms

  • 500 watts RMS per channel at 4 ohms

  • 330 watts RMS per channel at 8 ohms

  • 1400 watts at 4 ohms bridged

  • Weight Unpacked: 32.7

  • Dimensions: 19 X 17.5 X 3.5

  • Shipping Weight: 40.5 lb (18.4 kg)

PEAVEY CS800S

  • Power:
    600 Watts RMS per channel @ 2 Ohms

  • 400 Watts RMS per channel @ 4 Ohms

  • 260 Watts RMS per channel @ 8 Ohms

  • 1200 Watts @ 4 Ohms bridged

  • Dimensions:
    Unpacked Weight: 23.20 lbs.

  • Unpacked Width: 19 in.

  • Unpacked Depth: 16.8750 in.

  • Unpacked Height: 3.75 in.

  • Packed Weight: 27 lbs.

  • Packed Width: 21.3750 in.

  • Packed Depth: 23.50 in.

  • Packed Height: 7.50 in.

PEAVEY CS2000

 

Building on the reputation of the world-famous Peavey CS 800, which conquered the power amp market in the 1970s, the CS Series is the global standard bearer for workhorse reliability. Over the years, these amps have benefited from some of Peavey's most popular audio innovations, including Peavey's exclusive DDT compression/anti-clipping protection. With its 2RU design and power points up to 4080 watts, this latest evolution of the CS Series is leaner, louder and lighter than ever!

  • Features

  • 2-rack-space stereo power amp featuring DDT

  • 2 temperature-dependant variable speed fans

  • 1075 watts (RMS) per channel at 2 ohms

  • 760 watts (RMS) per channel at 4 ohms

  • 495 watts per channel at 8 ohms

  • 2150 watts at 4 ohms bridged

PEAVEY CS4080

 

Building on the reputation of the world-famous Peavey CS 800, which conquered the power amp market in the 1970s, the CS Series is the global standard bearer for workhorse reliability. Over the years, these amps have benefited from some of Peavey's most popular audio innovations, including Peavey's exclusive DDT compression/anti-clipping protection. With its 2RU design and power points up to 4080 watts, this latest evolution of the CS Series is leaner, louder and lighter than ever!

Features

  • 2-rack-space stereo power amp featuring DDT

  • 2 temperature-dependant variable speed fans

  • 2040 watts (RMS) per channel at 4 ohms

  • 1250 watts per channel at 8 ohms

  • 4080 watts at 4 ohms bridged

PEAVEY CS3000

 

Building on the reputation of the world-famous Peavey CS 800, which conquered the power amp market in the 1970s, the CS Series is the global standard bearer for workhorse reliability. Over the years, these amps have benefited from some of Peavey's most popular audio innovations, including Peavey's exclusive DDT compression/anti-clipping protection. With its 2RU design and power points up to 4080 watts, this latest evolution of the CS Series is leaner, louder and lighter than ever!

Features

  • 2-rack-space stereo power amp featuring DDT

  • 2 temperature-dependant variable speed fans

  • 1550 watts (RMS) per channel at 2 ohms

  • 1065 watts (RMS) per channel at 4 ohms

  • 650 watts per channel at 8 ohms

  • 3100 watts at 4 ohms bridged

PEAVEY XR8300

 

They feature new improved low noise mic preamps, multi point clip sampling and a new subsonic filter to prevent low frequency power robbing. New graphic equalizers have multi-Q bandwidth to allow some filters to perform feedback control while others perform tone control and have Peavey's patented FLS (Feedback Locating System).

Features

  • 8 improved, low-noise mic preamps

  • 10 line inputs

  • 48 Volt phantom power, 3 band EQ, monitor send and effects send on each channel

  • 25 dB pad on ch 1-6

  • Signal and Clip indicator on each channel

  • Dual Main or Main/Mon power amp mode switch

  • Dedicated 7 band Graphic for mains and monitors with FLS

  • DDT speaker protection

  • DSP based effects with parameter control

  • Channel mute switch

  • Rugged plastic case

  • 300W/channel @ 4 ohms

PEAVEY XR8600

 

They feature new improved low noise mic preamps, multi point clip sampling and a new subsonic filter to prevent low frequency power robbing. New graphic equalizers have multi-Q bandwidth to allow some filters to perform feedback control while others perform tone control and have Peavey's patented FLS (Feedback Locating System).

Features

  • 8 improved, low-noise mic preamps

  • 10 line inputs

  • 48 Volt phantom power, 3 band EQ, monitor send and effects send on each channel

  • 25 dB pad on ch 1-6

  • Signal and Clip indicator on each channel

  • Dual Main or Main/Mon power amp mode switch

  • Dedicated 7 band Graphic for mains and monitors with FLS

  • DDT speaker protection

  • DSP based effects with parameter control

  • Channel mute switch

  • Rugged plastic case

  • 600W/channel @ 4 ohms